Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Dryer Vent Cleaning for Glendale Homeowners
A clogged dryer vent is one of the most overlooked fire hazards in a Glendale home, and most homeowners don’t realize there’s a problem until the dryer takes two cycles to finish a single load. Dryer vent cleaning in Glendale typically costs between $129 and $229 for a standard single-story home with a short, straight vent run, and most jobs are completed in under an hour. Glendale Chimney Sweep handles the full scope of vented-combustion safety – chimney sweeping, chimney repair, and dryer vent cleaning – which means we approach your dryer exhaust with the same technical rigor we apply to fireplace flues. Call (833) 467-6493 to schedule a dryer vent cleaning with Noel Tarkanian and the team.

What separates us from a generalist handyman with a shop vac is the way we diagnose. We don’t just clear the lint you can see. We check airflow at the termination point, inspect the full vent run length, and flag transitions, sagging sections, or improper terminations that are quietly accumulating lint. Most Glendale homes we visit were built between the 1930s and 1970s, and a lot of those dryer vents were installed with materials and routing that would never pass code today. We’ll tell you exactly what you have, what it needs, and whether anything can safely wait.
What Our Dryer Vent Cleaning Service Includes
Every dryer vent cleaning we perform in Glendale is a full-system service, not a quick poke at the lint trap. Here’s what’s covered when we arrive:
Complete Vent Line Cleaning
We clean the entire vent run from the dryer connection at the wall to the exterior termination point. That includes the transition duct behind the dryer – the short, often-crushed aluminum section that’s secretly responsible for a huge share of lint accumulation and airflow restriction. In Glendale homes where the laundry room backs up to an exterior wall, this is usually a 5 to 10 foot run and takes about 20 minutes. When the dryer is in a central hallway or upstairs near the bedrooms – common in the older Spanish Revival and Mediterranean stock around Rossmoyne and Adams Hill – the run can stretch 15 to 25 feet with multiple elbows, and that takes longer to do properly. We use rotary brush equipment that scrubs the full circumference of the vent interior, not just whatever a straight rod happens to push loose.

Lint Trap and Housing Cleaning
The lint screen catches maybe 25 percent of what your dryer produces. The rest travels downstream and packs into the walls of the vent pipe. We remove and clean the lint trap housing, vacuum out the cavity below the trap, and check the felt seal on the trap itself – a worn seal lets lint slip past and into the blower assembly. This is the part most homeowners can see, but we’re also checking what it tells us: excessive lint at the trap after every load is a sign the vent line itself is already restricted. Glendale Chimney Sweep includes this in every dryer vent cleaning at no added charge because skipping it makes the rest of the work pointless.

Exterior Vent Hood and Termination Inspection
Feet from the ground is where most problems hide in plain sight. We inspect the exterior vent hood for a functioning damper, a proper pest screen, and a termination point that’s at least 12 inches off the ground per common code. Glendale’s dry heat doesn’t mean dryer lint stays harmless – it means it’s even more combustible. If the hood’s flapper is stuck open or missing, warm air from the dryer becomes a two-way street: lint out, birds and rodents in. We clean the hood, test the damper, and report any damage. Birds love making a nest on an un-screened dryer vent, and we’ve pulled nesting material out of vents that also serve heat-pump dryers up in the hills around Glenoaks Canyon.

Airflow Verification
After cleaning, we verify the system is actually moving air at a velocity that will carry moisture and lint out of the home. A backpressure reading tells us more than a visual check ever will, and we take it at the dryer connection point. If airflow is still poor after cleaning, that means there’s a restriction we didn’t remove – a collapsed section, a separated joint, or an internal transition issue. Most dryer vent companies in Glendale skip this and wave goodbye. We’d rather tell you the truth while we’re there than have you discover it three months later when the dryer starts failing again. The verification step is what turns a $150 cleaning into a documented maintenance visit with a baseline for next time.

Full Lint and Debris Removal
The job isn’t done until the floor around your dryer looks the way it did when we arrived. Every bit of lint, dust, and dryer debris we pull out of the vent gets bagged and removed. That matters more in a Glendale laundry room than most people think: fine dryer lint is a respiratory irritant, and if you have a gas dryer, you do not want lint piling up around an open flame. We also clean any lint we find inside the dryer cabinet itself where accessible. You should be able to walk back into your laundry room and not be able to tell work was just performed, other than the fact that your dryer now finishes the way it used to.

What happens when you call
- 1
A real person answersNo phone trees — you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Styles & brands we work with





Brands We Service for Dryer Vent Cleaning
Most dryer vent cleaning companies work on the vent line and never touch the dryer itself. We take a different approach. Glendale Chimney Sweep is authorized to work with professional chimney-industry brands like Famco and Copperfield, which means we stock and specify the same termination hoods, connectors, and vent components that professional contractors install. When we find a crushed transition duct or a rusted hood during a cleaning, we can replace it that day with a named, spec-grade part rather than whatever generic piece is on the shelf at the hardware store.
We also work daily with units connected to DuraFlex venting systems, and our experience with those liner systems gives us an edge when diagnosing vent configurations that other crews write off as too complex. Whether you have a Whirlpool, LG, Samsung, Maytag, or any other dryer make, the vent run follows the same physics and the same failure points. Our brand-specific knowledge means we name the exact material we’re installing and why it’s right for your setup – never a vague reference to “quality parts.” You can read more about how we handle those materials on our home page.
Signs You Need Dryer Vent Cleaning Right Now
- Clothes take more than one cycle to dry. This is the single most reliable early indicator of a restricted vent line. When your dryer can’t push moist air out fast enough, the sensor reads wet clothes and keeps the cycle running. In Glendale, where most homes run the dryer year-round regardless of season, a gradually lengthening dry time is not a dryer problem – it’s an exhaust problem.
- The dryer or laundry room feels unusually hot during a cycle. Heat radiating from the dryer cabinet means the exhaust isn’t carrying heat away. That heat is baking lint inside the vent line, and lint is a documented combustible that contributes to thousands of U.S. house fires every year. We’re not going to scare-sell you, but if your dryer is overheating, schedule a cleaning before you run another load.
- You see lint accumulating around the exterior vent hood. If lint is building up on the outside of the termination point, there’s enough packed inside to be pushing debris out. Clean the visible lint so you don’t have a fire fuel pile sitting on the side of your house, then call us. The visible stuff is the overflow from what’s hiding in the pipe.
- The lint screen has a thin, even coating after every single load. Some lint on the screen is normal. A heavy or even film every time you check is not. That’s a sign that lint isn’t being caught effectively, which means more of it is traveling downstream. A worn or misaligned lint trap seal will let lint bypass the screen and pack into the blower housing. We check that seal during every cleaning visit.
- You can’t remember the last time the vent was cleaned. Most dryer manufacturers recommend an annual vent cleaning for a household that runs three or more loads a week. In a two-person Glendale household doing laundry twice a week, every two years is often sufficient – but if you’ve lived in the house for five years and never had it done, it’s overdue. The cost of cleaning is minimal compared to the cost of a premature dryer replacement.
Our Dryer Vent Cleaning Process – Step by Step
We work in a specific order because each step builds on the one before it. Here’s what your appointment looks like from knock to handshake:
- 1
Arrival and setup. We arrive in a marked van with floor protection, the rotary-cleaning equipment, and a commercial vacuum system that captures lint at the source before it can become airborne in your home. Our technician introduces himself, confirms access to the dryer and exterior vent, and lays down floor protection from door to laundry room. Setup takes about five minutes.
- 2
System inspection. Before we clean anything, we inspect the full vent run: the connection at the dryer, the wall penetration, any visible transition sections, and the termination point at the exterior. We’re looking for crushed flex duct, joints that have separated, visible sagging runs, improper termination height, and evidence of pest intrusion. This inspection tells us whether the cleaning is straightforward or whether we’ll find a restriction mid-run.
- 3
Full-line cleaning. We run rotary brush equipment through the complete vent line from both directions, dislodging packed lint and scrubbing the full circumference of the pipe. No straight rods and no “good enough.” The vacuum system runs the entire time, capturing dislodged lint at the collection point rather than leaving it floating in your laundry room. We also clean the lint trap housing, the trap cavity, and the trap seal.
- 4
Airflow verification. With the vent line clean, we reconnect the dryer, run a brief cycle, and measure backpressure and airflow at both ends of the system. This confirms the vent is moving air at a rate that will keep your dryer efficient and safe. If we still see poor airflow, we start looking for what we haven’t found yet rather than calling the job complete. This is the step that separates a proper vent cleaning from a drive-by service.
- 5
Cleanup and report. We bag and remove every bit of lint, vacuum the work area, and walk you through exactly what we found and did. You’ll see the lint we removed and hear our specific recommendations if we spotted anything that needs attention – whether that’s a soon-to-fail transition duct or a termination hood that should be replaced. Then we’re out. The whole visit typically takes 45 to 75 minutes depending on access and vent length.
For broader venting-safety work beyond the dryer, see what else falls under our Dryer Vent Cleaning in Glendale scope.

See the difference
Before
After
Before
After
Before
AfterHow Much Does Dryer Vent Cleaning Cost in Glendale?
A standard dryer vent cleaning in Glendale runs $129 to $229 for a typical single-family home with a vent run of 15 feet or less and reasonable access at both ends. Homes with longer runs, multiple elbows, or a second-story rooftop termination – common in the hillside neighborhoods around Whiting Woods and Verdugo Viejo – run $179 to $329, because those jobs require more time, more equipment, and sometimes ladder work at the termination point. Condos and apartments in downtown Glendale and the Brand Boulevard corridor generally fall in the $99 to $169 range when the vent is short and fully accessible.
What changes the price: total vent length, number of elbows, termination height and access, whether there’s an existing pest screen or hood that needs removal, and whether the vent line is a rigid metal pipe or old flexible foil that’s deteriorated. Foil flex duct is often the culprit in restricted systems, and we’ll quote replacement separately rather than bury it as an upsell. What does not change the price: our flat pricing structure means you’ll know the cost before we start, and you’ll never be surprised by a final number. Every Glendale Chimney Sweep estimate includes the full inspection, the cleaning itself, and the airflow verification – nothing hidden.
How to avoid overpaying: get a written flat price before booking, not an hourly rate. Ask whether the company measures airflow or just pushes a brush through. Ask whether they clean the lint trap housing or just the vent line. And ask whether your quote includes the exterior hood inspection. If those items aren’t named, you’re paying for a partial job. Call (833) 467-6493 for a free estimate that spells out exactly what’s included.
Dryer Vent Cleaning Near Glendale – Our Service Area
Glendale Chimney Sweep serves Glendale and the surrounding communities including Dryer Vent Cleaning in Silver Lake, Dryer Vent Cleaning in Burbank, Echo Park, Hollywood, La Cañada Flintridge, Universal City, South Pasadena, Los Angeles, La Crescenta-Montrose, Pasadena, and Koreatown. If you’re within 30 to 45 minutes of our Glendale base, we can typically schedule you within the week, and many dryer vent cleanings can be booked with just a day or two of notice depending on the season. Our team knows the housing stock in each of these areas – the same 1940s bungalow layout we see near Atwater Village shows up in Koreatown and Silver Lake, and that means we know where the vent runs hide.
Serving Glendale, CA — Our Local Coverage Area
We’re based in the Glendale area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
Frequently Asked Questions – Dryer Vent Cleaning in Glendale
Dryer vent cleaning is the process of removing accumulated lint, debris, and obstructions from the full vent line that carries hot, moist air from your dryer to the exterior of your home. It includes cleaning the vent line itself, the lint trap housing, and the exterior termination hood to restore proper airflow. Glendale Chimney Sweep performs this as a full-system service with airflow verification at the end, not just a visual pass-through.
A standard dryer vent cleaning takes between 45 and 75 minutes from arrival to final walkthrough. Short, straight vent runs in single-story homes are on the faster end, while multistory homes with long or offset runs take closer to 75 minutes. We factor in the full inspection, cleaning, airflow verification, and cleanup – so you’re not watching the clock wondering when we’ll actually start.
Most dryer vent cleanings in Glendale run $129 to $229 for a typical single-family home. Longer runs, rooftop terminations, and hillside access can push the price to $329 in some cases, while condos and apartments are often $99 to $169. The price is flat and disclosed before we begin, never hourly. Call (833) 467-6493 and we’ll give you an exact quote over the phone.
Yes, we clean the vent systems for every major dryer brand including Samsung, LG, Whirlpool, Maytag, GE, and Electrolux. The vent line and termination point are the same regardless of dryer manufacturer, and our inspection covers the full system rather than the dryer’s internal components. What matters more than the dryer brand is the vent configuration, and we’ve handled everything from short direct runs to 25-foot offset systems in older Glendale homes.
If your dryer is overheating, producing a burning smell, or failing to exhaust at all, stop using it and call us right away. We prioritize safety-related calls and will typically schedule you as quickly as our Glendale technician’s route allows, often same-day or next-day depending on the situation. Do not run the dryer until the vent has been inspected. We also perform chimney sweeping and chimney repair if you have a fireplace that needs attention at the same visit.
We stand behind the quality of the cleaning itself. If you’re not satisfied with the work within 30 days, call us and we’ll make it right at no charge. We can’t warranty against future lint accumulation – your dryer produces new lint every cycle – but we will verify proper airflow at the end of every visit and document it so you have a baseline. Material replacements we install, like a new termination hood or transition duct, carry the manufacturer’s stated warranty.
Clear a path to the dryer and remove any items stacked on top of it. If the dryer is in a closet, remove anything stored in front of the dryer or on the floor around it. We’ll handle moving the dryer itself – no need to disconnect anything. If the exterior vent is behind a gate or in a fenced yard, make sure it’s unlocked or let us know in advance so we can plan access. That’s all the preparation we need.
Schedule Your Dryer Vent Cleaning Service in Glendale Today
A dryer vent that’s never been cleaned is a fire hazard that compounds every time you run a load. The fix is inexpensive, takes under an hour, and we show you exactly what we pulled out of your vent so you’re never guessing. Call (833) 467-6493 for a free, no-obligation estimate from Noel Tarkanian and the Glendale Chimney Sweep team. One call covers your fireplace, chimney, and dryer vent.
Written by Noel Tarkanian, Owner at Glendale Chimney Sweep, serving Glendale and surrounding communities.